Understanding The PVC Conveyor Belt Tracking And Its Significance!

When considering the many options available selecting a PVC Conveyor Belt is often the most cost-effective option. When the belt is required to fulfil certain specifications, such as performing small transfers, having excellent releasing capabilities, or having a high level of resistance to oils and greases. It is essential to determine whether alternative belt materials have the potential to meet the requirements of the manufacturing process.?

In addition to choosing the right type of belt to suit your application is the accurate tracking technique. A PVC Conveyor belt requires proper check-up and tracking for high efficiency and efficacy.?

PVC Conveyor Belt Tracking 

The technique of aligning and manipulating a conveyor belt, in such a way that it travels along the specified route gets referred to as conveyor belt tracking. Adjusting the belt’s idlers, pulleys, and loading conditions get referred to as “tracking” and is a technique used to regulate and correct any inclination of the belt to run in an unintended direction. 

Techniques To Track A PVC Conveyor Belt

Tracking a conveyor belt is essential, but it does not have to be difficult to be effective. 

The following are three simple procedures that may get used to tracking a conveyor belt.

  • While the conveyor is running, the bolts closest to the tail pulley should have their torque reduced. It will cause the snub roller, which is the major mechanism used for directing the conveyor belt to become slacker.
  • Tap the bolts with a rubber mallet in the direction you want the conveyor belt to go. You may do this either way. Because of this, the snub roller will start to move. Be careful to retighten the bolts on the snub roller after any necessary adjustments to ensure that it remains in a new position.
  • It is necessary to repeat Steps 1 and 2 as many times as necessary until the centre of your conveyor belt is within a quarter-inch of the centre of the tail pulley. Take caution not to make any significant changes at this time. A seemingly small alteration may result in a significant shift. You must begin with the snub rollers located closest to the extremities of the conveyor and work your way toward the middle of the conveyor. 

How to Repair the Tracking of a Conveyor Belt

There are actions you may do to maintain your conveyor belts, and there are also actions you should take when there are problems with the tracking of conveyor belts. Both sets of action pertain to tracking conveyor belts.

If you are experiencing difficulties with the alignment of the conveyor belt, the following are some things to keep an eye out for! 

Verify That The Pulleys Are Square!

Installers of conveyor belts may sometimes rotate the end pulley to track the conveyor belt. Sadly, doing so might make the situation much worse. Instead, the belt should be guided by the snub rollers or idlers as was originally designed.

Check If The Frame Of The Conveyor Is In Accurate Level! 

A significant portion of the problems that occur with the tracking of conveyor belts is brought on by the track not being level or square. The leading PVC Conveyor Belt Manufacturers In India suggest that the belt on your conveyor will shift to one side or the other if it is not level or square.?

It is possible to examine the levelness of your conveyor system in a hurry by using a standard level. It is essential to examine the pulleys and the frames to ensure they are level. Measurements should be taken from one corner of the conveyor bed to the opposite corner on either side of the conveyor belt. It will ensure that the bed of the conveyor is square. The measurements must be comparable. If they are not, the squaring rods get located on the underside of the conveyor may get utilised to bring the system in one alignment. 

Examine Your PVC Conveyor Belt For Any Foreign Material

It is essential to do a thorough inspection of conveyor belts. Checking not only for technical problems but for cleanliness is crucial. A crown, also known as a raised section on a pulley, may form if a material such as a tape or other substances accumulates on either one of the end pulleys or both of them. Because of this, there will be issues with the tracking of the conveyor belt.  

Look For Expert Manufacturers & Suppliers!?Manufacturing faults might cause the tracking issues you get to see with your conveyor. Therefore, it is prudent to get it from legitimate suppliers like DKT Engineering Enterprises. We are the leading PVC Conveyor Belt Suppliers In India. Our products are readily available in every market. If you want to place your order online, all you have to do is, visit our website and contact us.